Error type number | Error type | What to do? | Description |
---|---|---|---|
001 | Short-circuit | Electrical inspection: Cable, sensor contacts | Conduct short-circuit test. |
002 | Interruption | Electrical inspection: Cable, sensor contacts | Conduct interruption test. |
003 | Short-circuit | Electrical inspection: Cable, sensor contacts | Conduct short-circuit test. |
004 | Interruption | Electrical inspection: Cable, sensor contacts | Conduct interruption test. |
005 | Sensor outside area | Mechanical damage, teach/calibrate, | Check sensor for mechanical damage, then teach/calibrate sensor |
006 | Sensor not taught | Teach/calibrate sensor | Sensor not taught/calibrated. Conduct teaching. |
007 | Electronics undervoltage | Undervoltage electronics ECUpwr Check electric system tractor/basic. Electrical inspection according to circuit diagram: cables, plug-and-socket connections |
Supply voltage too low |
008 | Electronics overvoltage | Overvoltage electronics ECUpwr Check electric system of tractor/basic machine. |
Supply voltage too high |
009 | Power undervoltage | Undervoltage ISOBUSpwr output Electrical inspection: Supply isobus, cables, contacts, power supply, tractor |
Supply voltage too low |
010 | Power overvoltage | Overvoltage electronics ECUpwr Check electric system of tractor/basic machine. |
Supply voltage too high |
011 | CAN BUS overflow | Too many message on CAN BUS, possibly malfunction of a subscriber. Check terminating resistors |
Too many messages on the CAN BUS. |
012 | CAN communication error | Check terminating resistors, wiring, plug-and-socket connections as well as affected control units. | Time exceeded for communication with one or several subscribers. |
013 | Standard parameter set | Enter vehicle-specific parameter set manually or load with ServiceTool. | Control unit was reset to default parameter set. Possible causes: Wrong shut-off of the ECU by unplugging during operation, loose contact or battery buffer. |
014 | Slave communication error | Check power supply of module concerned or replace module | If power is available, internal fault in control unit. |
015 | Master communication error | Check power supply of module concerned or replace module | If power is available, internal fault in control unit. |
016 | Addressing error | Restart addressing. | Module installed without or wrong addressing. |
017 | Wrong assignment | Electrical inspection: A master valve has possibly been plugged into an unassigned output. |
An additional master valve was subsequently plugged on a channel not assigned during addressing. |
018 | Busheavy | CAN Bus faulty, check CAN Bus wiring | Electrical fault in CAN BUS system |
019 | Buslight | CAN Bus faulty, check CAN Bus wiring | Electrical fault in CAN BUS system |
020 | Busoff | CAN Bus faulty, check CAN Bus wiring | Electrical fault in CAN BUS system |
021 | Manual override on | Restart system or shut off manual overlay. | One or several inputs were overlaid with a manual value in the diagnostics menu. |
022 | Current too high | Electrical inspection according to circuit diagram. Wiring, consumer, control unit. |
Permitted current at the respective output of the control unit concerned exceeded. |
023 | Partial failure | Electrical inspection according to circuit diagram. Wiring, control unit. Use control unit-specific diagnostic tool. |
Restricted function of the respective control unit. |
040 | Current too high Prio2 | Check electric system tractor/basic machine on master side. | Disabling Prio2 consumers through central electrics power management due to overcurrent. |
041 | Current too high Prio3 | Check electric system tractor/basic machine on master side. | Disabling Prio3 consumers through central electrics power management due to overcurrent. |
042 | Undervoltage Prio2 | Check electric system tractor/basic machine on master side. | Disabling Prio2 consumers through central electrics power management due to undervoltage. |
043 | Undervoltage Prio3 | Check electric system tractor/basic machine on master side. | Disabling Prio3 consumers through central electrics power management due to undervoltage. |
044 | Current too high Prio2 | Check electric system tractor/basic machine on slave side. | Disabling Prio2 consumers through central electrics power management due to overcurrent. |
045 | Current too high Prio3 | Check electric system tractor/basic machine on slave side. | Disabling Prio3 consumers through central electrics power management due to overcurrent. |
046 | Undervoltage Prio2 | Check electric system tractor/basic machine on slave side. | Disabling Prio2 consumers through central electrics power management due to undervoltage. |
047 | Undervoltage Prio3 | Check electric system tractor/basic machine on slave side. | Disabling Prio3 consumers through central electrics power management due to undervoltage. |
048 | Excess voltage | Check electric system of control unit mentioned. | Overvoltage in the supply of the respective control unit |
049 | Short-circuit to ground | Check electric system of component mentioned. | Short-circuit to earth on outputs of travel drive switched via earth. |
050 | Short-circuit | Check the electric system. | Short-circuit to supply voltage. |
051 | Undervoltage | Electrical inspection according to circuit diagram. Wiring, plug-and-socket connections, travel direction switch, control unit. |
Undervoltage in the supply of the respective control unit |
052 | Outside of range | Electrical inspection according to circuit diagram. Wiring, plug-and-socket connections, control unit. |
Voltage levels, signals from sensors, etc. are not in the defined range |
053 | Interruption | Electrical inspection: Cables, contacts, | Component was disconnected from control unit. |
054 | Critical current | Electrical inspection: Cables, contacts, | Current level outside valid range but no short-circuit yet. This may cause damages in the long run. |
059 | HECU int error | Flash software again. Replace control unit. |
Internal control unit fault |
060 | Defective | Electrical inspection: Cables, contacts, | Outputs or magnets defective |
061 | Time exceeded | Switch control unit | H-bridges or inputs defective |
062 | Blocked | Electrical inspection according to circuit diagram. Wiring, control unit. Check mechanical condition of water valve. |
Current consumption of water valve too high. |
063 | Min. current not reached | Check mechanical condition of water valve. | Current consumption of water valve too low; possibly transmission damage. |
064 | Analysing failed | Developer error: Parsing of objects for Pool ABT/Dashboard failed | Pool needs to be revised |
065 | Speed too low | Increase speed of piston diaphragm pump to reach required application quantity Adjust propshaft speed or hydraulics output control unit, depending on the design |
Pump speed inadequate |
066 | Rotation speed too high | Reduce speed of piston diaphragm pump to prevent damages. Adjust propshaft speed or hydraulics output of control unit, depending on the design |
Pump speed too high |
069 | Input faulty | ||
070 | Pool vers unsuitl | Flash released software according to released bundle. | Software version from LSB to ABT or HECU to dashboard not compatible |
071 | Level 1 | Service level 1 activated | |
072 | Level 2 | Service level 2 activated | |
079 | Road tyre pressure low | Increase tyre pressure | Insufficient tyre pressure may cause damage to the tyre |
080 | Tyre pressure too low | Increase tyre pressure | Insufficient tyre pressure may cause damage to the tyre |
081 | Tyre pressure too high | Lower tyre pressure | Excessive tyre pressure may cause damage to the tyre |
083 | low | Act according to the fault location | low |
084 | high | Act according to the fault location | high |
085 | too high | Act according to the fault location | too high |
086 | value invalid | Act according to the fault location | Value implausible |
087 | no communication | Act according to the fault location | Communication failure |
091 | Power supply too low | Increase supply voltage. Electrical inspection: Cables, contacts. |
Travel drive, battery voltage too low (smaller 9 V), vehicle looses moment, vehicle coasts. |
092 | Power supply too high | Lower supply voltage. Electrical inspection: Cables, contacts. |
Travel drive, battery voltage too high (greater 16 V), vehicle slows down via ramp and stops. Emergency operation possible |
093 | Power supply sensor 1 | Electrical inspection: Cables, contacts, sensors | Travel drive, sensor supply not within tolerance. Vehicle slows down via ramp and stops. Emergency operation possible |
094 | Power supply sensor 2 | Electrical inspection: Cables, contacts, sensors | Travel drive, sensor supply not within tolerance. Vehicle slows down via ramp and stops. Emergency operation possible |
100 | Successful closed | No action required | Action (see fault location) successfully completed |
101 | Not possible | Action according to fault location | Action (see fault location) cannot be executed |
102 | Was started | No action required | Action (see fault location) was started |
103 | Was stopped | No action required | Action (see fault location) stopped by user |
104 | Was stopped | Action according to fault location | Action (see fault location) stopped because of a fault |
105 | Diff. application quantity | Adjustment travel speed, nozzles, | Application quantity l/ha deviation too large |
106 | Filling limit reached | No action required | Filling limit reached |
107 | Please verify | Action according to fault location | Please verify |
108 | Fill funct active | Desired function cannot be started because of filling in progress | Filling function active |
109 | Spray funct activ | Desired function cannot be started because of spraying function in progress | Spraying function active |
110 | CAN protocol incompatible | Contact HORSCH Service | Development fault, CAN protocol of subscriber (see fault location) not as expected |
111 | Configuration error | Check configuration | Configuration error |
112 | Filter soiled | Cleaning the filter | Filter soiled |
113 | Chck nozzle selct | Select different nozzles. | Check nozzle selection |
114 | internal error | Contact HORSCH Service | internal error |
115 | Wing not synchronised | Check folding boom and machine | When folding, the pertaining wing pairs have exceeded a maximum allowed position difference. |
116 | Check folding boom position | Mechanically stopped, teach sensor | Folding boom not in end position |
117 | Steering not centred | Centre steering. | Rear axle steering not in centre position. It must be centred for the desired request. |
118 | Folding boom pressure insufficient | Increase folding boom pressure | Folding boom pressure too low |
119 | Wing lt/rt not unfolded | Unfold folding boom wing to end stop | Folding boom wing left right not unfolded |
120 | Check folding boom position | Action according to fault location | Check folding boom position |
121 | not calibrated | The system must be calibrated for the full range of functions. However, this has not happened with one area (see fault location) | |
122 | Configuration faulty | Check inputs / settings for correctness | Selected configuration not possible |
123 | Signal not available | ||
124 | Configuration accepted | Configuration accepted | |
125 | Configuration incomplete | Check inputs / settings for completeness | Configuration is not complete. |
126 | Configuration rejected | Inputs / settings must be made again. | Configuration not accepted |
127 | Machine is busy | Function(s) is/are executed No other functions can be activated. |
|
128 | Restart the machine | Disconnect power supply and then reconnect. | Machine must be restarted. |
129 | Stop machine | Machine must be stopped without delay. | |
130 | Not ready for starting | Check start conditions of function | Function cannot be started. |
132 | Parameter value invalid | Parameter value of another subscriber (see fault location) could not be accepted | |
133 | Fold only at standstill! | Stop machine and execute folding process again. Machine must not be moved during the folding process. | Folding boom folding may only be carried out at standstill. |
134 | Channel configuration error | If CAN OK: Run addressing teach again | Feedback of existing channels does not agree with configuration. |
135 | Function is deactivated | ||
136 | Filling quantity reduced! | ||
137 | Sensor value invalid | The value of a sensor (see fault location) is outside a valid range | |
139 | Hopper is full | Filling process must be stopped. | Tank has reached rated volume. |
140 | Res qty fall belw | Stop process, if necessary, to provide sufficient residual quantity for subsequent applications Replenish tank |
The defined residual quantity was fallen below Residual quantity no longer sufficient |
141 | Chem tank cont too low | Fill up solution tank so this function can be started. | The filling level wash container is too low for this function. |
142 | Chem tank cont too high | Reduce filling level wash container so this function can be started. | The filling level wash container is too high for this function. |
143 | Fresh water tank low | Fill up fresh water tank so this function can be started. | The filling level in the fresh water tank is too low for this function. |
144 | Fresh water tank too low | Increase filling level in fresh water tank so this function can be started. | The filling level in the fresh water tank is too low for this function. |
145 | Communication error | Communication of a CAN subscriber (see fault location) is interrupted longer than permitted | |
146 | Target position not reached | Check function of component (as per fault location). | Defined end position not reached (affected function as per fault location) |
147 | Residual quantity diluted! | ||
148 | Speed too low | ||
149 | Calibration aborted | Repeat calibration process. Contact service partner. |
Calibration aborted |
150 | Calibration stored | No action required | Calibration stored |
151 | Calibration value rejected | Repeat calibration. Contact service partner. |
Calibration value rejected |
152 | Calibration value accepted | No action required | Calibration value accepted |
153 | Field mode not possible | Field mode not possible | |
154 | Speed too high | Because of the current process on the folding boom the current speed is too high for the process on rear axle steering | |
159 | not in centre position | When switching from field mode to road travel mode and rear axle steering is not in the centre position | |
160 | not retracted | When switching from field mode to road travel mode and an object (see fault location) was not moved into road travel mode | |
161 | start | The engine must be started for the desired process | |
162 | not in field mode | The vehicle must be moved into field mode for the desired process | |
163 | too low | A value (see fault location) is too low for the desired process | |
164 | Placing quantity override | Placing quantity override | |
165 | Border nozzle active | Border nozzle active | |
166 | Edge nozzle active | Edge nozzle active | |
167 | End position not reached | Check the folding boom section for function and freedom of movement. | End position not reached |
168 | Release required | Function / parameter can be operated / changed only with enabling. | Release required |
169 | Access level 1 activated | Functions enabled under access level 1 | |
170 | Access level 2 activated | Functions enabled under access level 2 | |
171 | Selection/combination error | Selection/combination error | |
172 | Agitator is active | Agitator is active | |
173 | Vehicle must be stopped | Function can only be enabled / operated when the vehicle is stopped | Vehicle must be stopped |
174 | Note danger zone | Note danger zone | |
175 | Drive 100 m and confirm | A distance of 100 m must be travelled to calibrate the speed | |
176 | Check wing pos./interlock | Check folding boom wing and folding boom lock. | Check wing pos./interlock |
177 | Changeover cleaning cock | Manual valve for switching between inside / outside cleaning is in the wrong position. | Changeover cleaning cock |
178 | Inputs overlap | Inputs overlap | |
179 | Parameter value error | Parameter value error | |
180 | Not folded | Check folding boom wing and folding boom lock. | Folding boom (section) not folded |
181 | Not unfolded | Check folding boom wing and folding boom lock. | Folding boom (section) not unfolded |
182 | Changeover cleaning cock | Manual valve for switching between inside / outside cleaning is in the wrong position. | Changeover cleaning cock |
183 | Voltage too low | Voltage too low | |
184 | Calibration not correct | Calibration not correct | |
185 | Curve speed too high | Adjust travel mode in curves to avoid damages to the folding boom. | Cornering speed too high. |
186 | Folding boom height invalid | Folding boom height invalid. | |
187 | Travel speed invalid | Sensor does not supply a plausible signal. Replace speed source if necessary. |
Invalid speed signal |
188 | Simulation speed active | Switch to wheel, GPS or radar speed on the speed side. | Speed signal is simulated. |
189 | Sensor must be pressureless | Ensure the system is depressurised. | Pressure is applied to the sensor. Zero-bar teach cannot be carried out. |
190 | Wrong teach direction | Function must be operated in opposite manner. Check installation position of sensor. |
Sensor not at the right position |
191 | Sensor value wrong | Check / replace sensor. Check sensor fastening |
Sensor value wrong |
192 | Sensor meas. jumps too large | Check / replace sensor. Check sensor fastening |
Sensor meas. jumps too large |
193 | Sensor value change missing | Check / replace sensor. Check sensor fastening |
Sensor value change missing |
194 | Sensor fault wrong distance | Check / adjust distance between sensor and encoder | Sensor fault wrong distance |
195 | Teach-Check internal error | Teach-Check internal error | |
196 | Insufficient system dynamics | Insufficient system dynamics | |
197 | Insufficient system cinematics | Insufficient system kinematics | |
198 | Intervention in control | Intervention in BoomControl | |
199 | Check folding boom position | The parallelogram is not correctly in the rest position. Hook not properly engaged. Check folding boom | |
209 | Temperature too high | Permissible working temperature for an object (see fault location) was exceeded | |
301 | ADAS not connected | ADAS not connected | |
302 | IMU error | IMU error | |
303 | Laser scanner error | Laser scanner error | |
304 | GPS error | Ensure sight contact to satellite. Check GPS receiver. |
No satellites available. Malfunction of GPS receiver |
305 | Bootloader loop | Bootloader loop | |
393 | Subsystem signal error | The subsystem registered at the fault location signals an error. Additional error information may be available in the pool of the subsystem. | |
394 | Check nozzles | Check nozzles | |
399 | in transport position | Move suspension to working position before driving off | The suspension is in transport position |
400 | not in working position | Move suspension to working position before driving off | The suspension is not in transport or working position |
401 | not released | Hydraulics released | Hydraulic function deactivated |
Error location number | Error location | Description |
---|---|---|
0097 | Raven subsystem | Raven Product Controller II or Raven pulse nozzles |
0176 | Flow meter folding boom | Flow meter folding boom |
0177 | Pressure sensor folding boom | Spraying pressure sensor folding boom |
0179 | Angle sensor inside wing - middle wing 1 left | Angle sensor inside wing - middle wing 1 left |
0180 | Angle sensor inside wing - middle wing 1 right | Angle sensor inside wing - middle wing 1 right |
0181 | Pressure sensor centrifugal pump | Pressure sensor water-side centrifugal pump |
0182 | Angle sensor inside wing right damping | Angle sensor inside wing right horizontal damping |
0183 | Angle sensor interlock inside left | Angle sensor interlocking inside left |
0184 | Chemical filling level 2 | Filling level sensor wash tank 2 |
0185 | Filling level sensor, fresh water | Filling level sensor, fresh water tank |
0186 | Cleaning pressure sensor | Internal cleaning pressure sensor |
0187 | Filling level sensor, chemical | Filling level sensor wash tank |
0188 | Agitator pressure sensor | Agitator pressure sensor |
0189 | Wheel speed sensor | Wheel speed sensor |
0190 | Preload pressure horizontal damping pressure sensor | Preload pressure horizontal damping pressure sensor |
0191 | Tyre pressure control system | Tyre pressure control system |
0195 | Parallelogram folding boom height sensor | Angle sensor parallelogram folding boom height |
0196 | Angle sensor interlocking outside left | Angle sensor interlocking outside left |
0197 | Package locking right angle sensor | Package locking right angle sensor |
0198 | Outside wing left angle sensor | Outside wing left angle sensor |
0199 | Outside wing right angle sensor | Outside wing right angle sensor |
0200 | Angle sensor interlocking outside right | Angle sensor interlocking outside right |
0201 | Package locking left angle sensor | Package locking left angle sensor |
0202 | Middle wing left angle sensor | Middle wing left angle sensor |
0203 | Middle wing right angle sensor | Middle wing right angle sensor |
0204 | Interlocking inside right angle sensor | Interlocking inside right angle sensor |
0205 | Pendulum lock angle sensor | Pendulum lock angle sensor |
0206 | Inside wing left damping angle sensor | Angle sensor inside wing left horizontal damping |
0207 | Solenoid valve inside wing folding | Solenoid valve inside wing folding |
0208 | Solenoid valve inside wing unfolding | Solenoid valve inside wing unfolding |
0209 | Solenoid valve middle wing folding | Solenoid valve middle wing folding |
0210 | Solenoid valve middle wing unfolding | Solenoid valve middle wing unfolding |
0211 | Solenoid valve lower folding boom | Solenoid valve lower parallelogram |
0212 | Solenoid valve lift folding boom | Solenoid valve lift parallelogram |
0213 | Solenoid valve piston diaphragm pump | Solenoid valve piston diaphragm pump |
0214 | Solenoid valve proportional centrifugal pump | Solenoid valve proportional centrifugal pump |
0215 | Filter backflushing valve | Pressure filter rinsing water valve |
0216 | Solenoid valve retract left suspension cylinder | Solenoid valve retract left horizontal suspension |
0217 | Solenoid valve reduce suspension preload pressure | Solenoid valve lower horizontal suspension preload pressure |
0218 | Solenoid valve extend left suspension cylinder | Solenoid valve extend left horizontal suspension |
0219 | Solenoid valve extend right suspension cylinder | Solenoid valve extend right horizontal suspension |
0220 | Solenoid valve high pressure cleaner | Solenoid valve high pressure cleaner |
0221 | Solenoid valve increase suspension preload pressure | Solenoid valve increase horizontal suspension preload pressure |
0222 | SV pendulum lock | Solenoid valve pendulum lock |
0223 | Solenoid valve retract right suspension cylinder | Solenoid valve retract right horizontal suspension |
0224 | CAN enable (switch-on voltage for control units) | CAN enable (switch-on voltage for control units) |
0225 | Solenoid valve LS pump activation | Solenoid valve LS pump activation (electrical LS signal) |
0226 | SV pendulum lock | Solenoid valve pendulum lock |
0227 | Solenoid valve left angling up | Solenoid valve bending left inside up |
0228 | Solenoid valve left angling down | Solenoid valve left inside angling down |
0229 | SV angle lt. outside up | Solenoid valve left outside angling up |
0230 | SV angle lt. outside down | Solenoid valve left outside angling down |
0231 | SV angle rt. inside up | Solenoid valve right inside angling up |
0232 | SV angle rt. inside down | Solenoid right inside angling down |
0233 | SV angle rt. outside up | Solenoid valve right outside angling up |
0234 | SV angle rt. outside down | Solenoid valve right outside angling down |
0235 | Supply EB09 UB+ | Power supply LSB / JR ESX-3XM EB09 UB+ |
0236 | Supply EB04 UB+ | Power supply LSB / JR ESX-3XM EB04 UB+ |
0237 | Supply EB05 UB+ | Power supply LSB / JR ESX-3XM EB05 UB+ |
0238 | Supply 3XM UB1+ | Power supply LSB / JR ESX-3XM UB1+ |
0239 | Supply voltage Electronics | Power supply LSB / JR ESX-3XM Electronics |
0240 | Terminal 15 signal | Signal terminal 15 LSB / JR ESX-3XM |
0241 | Angle sensor right rear axle steering angle | Steering angle sensor right |
0242 | Angle sensor left rear axle steering angle | Steering angle sensor left |
0243 | External filling stop | |
0244 | Filling horn | |
0247 | Wheel speed sensor | Wheel speed sensor |
0249 | Solenoid valve rear axle steering left | Solenoid valve steering left |
0250 | Solenoid valve rear axle steering right | Solenoid valve steering right |
0251 | Solenoid valve outside wing folding | Solenoid valve folding outside wing |
0252 | Solenoid valve outside wing unfolding | Solenoid valve unfolding outside wing |
0253 | Solenoid valve seat valve steering axle A interlocking | Lock valve steering axle left |
0254 | Solenoid valve seat valve steering axle B interlocking | Lock valve steering axle right |
0255 | Solenoid valve open package locking | Solenoid valve open package locking |
0256 | Solenoid valve close package locking | Solenoid valve close package locking |
0257 | Folding boom blow-out valve | Blow out water valve folding boom (AIR valve) |
0259 | Solenoid valve lift right middle section | Solenoid valve lift right slope compensation |
0260 | Magnetventil Mittelteil links heben | Solenoid valve lift left slope compensation |
0261 | Supply IOX terminal 30 | Supply IOX terminal 30 |
0262 | Control units power IOX terminal 15 | Control units power IOX terminal 15 |
0263 | Supply IOX terminal 30 | Supply IOX terminal 30 |
0264 | Supply IOX terminal 31 | Supply IOX terminal 31 |
0265 | Supply IOX terminal 32 | Supply IOX terminal 32 |
0267 | Slope comp. pressure LH. | Pressure sensor slope compensation left |
0268 | Slope comp. pressure RH. | Pressure sensor slope compensation right |
0269 | BC ISOBUS PWR | Power supply control unit BCIO (Boom Control) output |
0270 | BC ECU PWR | Power supply electronics control unit BCIO (Boom Control) output |
0271 | LVC ISOBUS PWR | Power supply control unit LVC (Liquid Valve Controller) output |
0272 | LVC ECU PWR | Power supply electronics control unit LVC (Liquid Valve Controller) |
0273 | Cruise control | Cruise control |
0274 | Travel direction | Direction of travel |
0275 | Rear axle steering | rear axle steering |
0276 | Speed | Speed |
0278 | Machine settings | |
0279 | Access level | Access level |
0283 | Buffer circuit | Battery buffer circuit |
0284 | SV parallelogram left | Solenoid valve parallelogram lock left |
0285 | SV parallelogram right | Solenoid valve parallelogram lock right |
0286 | Border nozzle left | Border nozzle left |
0287 | Border nozzle right | Border nozzle right |
0288 | Edge nozzle left | Edge nozzle left |
0289 | Edge nozzle right | Edge nozzle right |
0290 | Hydraulic compressor | Hydraulic compressor |
0291 | Wind meter | Wind meter |
0292 | SV special flaps out | Solenoid valve unfolding special flaps |
0293 | SV special flaps in | Solenoid valve folding special flaps |
0330 | Pre-selection unfolding | Solenoid valve pre-selection unfolding |
0331 | Pre-selection folding in | Solenoid valve pre-selection folding in |
0332 | SV inside wing right off | Solenoid valve unfolding right inside wing |
0333 | SV inside wing right on | Solenoid valve folding in right inside wing |
0467 | Sensor hydraulic filter | Sensor hydraulic filter |
0468 | LVC WV11 | LVC Liquid Valve Controller water valve 11 / 2-way valve |
0469 | LVC WV12 | LVC Liquid Valve Controller water valve 12 / 2-way valve |
0470 | ZE | Central electrics circuit board |
0471 | ZE Kl.15 ESX | Voltage central electrics circuit board terminal 15 ESX |
0472 | ZE ECU pwr 1 | Control unit power supply (CE) Central electrics circuit board Power 1 |
0473 | ZE ECU pwr 2 | Control unit power supply (CE) Central electrics circuit board Power 2 |
0474 | ZE ECU pwr 3 | Control unit power supply (CE) Central electrics circuit board Power 3 |
0475 | ZE LVC pwr | Power supply Central Electrical System (ZE) control unit - Liquid Valve Controller (LVC) |
0476 | ZE Ue 1 | Power supply central electrics Electronics 1 |
0477 | ZE Ue 2 | Power supply central electrics Electronics 2 |
0478 | ZE Ue 3 | Power supply central electrics Electronics 3 |
0479 | ZE Ue 4 | Power supply central electrics Electronics 4 |
0480 | ZE Ue 5 | Power supply central electrics Electronics 5 |
0481 | ZE Ue 6 | Power supply central electrics Electronics 6 |
0482 | ZE UL 1 | Power supply central electrics Output 1 |
0483 | ZE UL 2 | Power supply central electrics Output 2 |
0484 | ZE UL 3 | Power supply central electrics Output 3 |
0485 | ZE UL 4 | Power supply central electrics Output 4 |
0486 | ZE UL 5 | Power supply central electrics Output 5 |
0487 | ZE UL 6 | Power supply central electrics Output 6 |
0488 | ZE UL 7 | Power supply central electrics Output 7 |
0489 | ZE UL 8 | Power supply central electrics Output 8 |
0490 | ZE UL 9 | Power supply central electrics Output 9 |
0491 | ZE ID20 | Central electrics circuit board |
0492 | ZE UL 13 | Power supply central electrics Output 13 |
0493 | ZE UL 14 | Power supply central electrics Output 14 |
0494 | ZE UL 15 | Power supply central electrics Output 15 |
0495 | ZE UL 16 | Power supply central electrics Output 16 |
0496 | ZE UL 17 | Power supply central electrics Output 17 |
0497 | ZE UL 18 | Power supply central electrics Output 18 |
0498 | ZE UL 19 | Power supply central electrics Output 19 |
0499 | ZE UL 20 | Power supply central electrics Output 20 |
0500 | ZE CAN en | Power supply central electrics circuit board CAN enable (switch-on voltage for control units) |
0501 | ZE UB+ ESX EB09 | Power supply Output Central electrics circuit board job computer (LSB) EB 09 |
0502 | ZE UB+ ESX EB04 | Power supply Output Central electrics circuit board job computer (LSB) EB 04 |
0503 | ZE UB+ ESX EB05 | Power supply Output Central electrics circuit board job computer (LSB) EB 05 |
0504 | ZE UB+ ESX | Power supply Output central electrics circuit board job computer (LSB) EB |
0505 | ZE Ue+ ESX | Power supply Electronics central electrics circuit board job computer (LSB) EB |
0506 | ZE UB+ IOX1 | Power supply Output central electrics circuit board IOX1 |
0507 | ZE Ue+ IOX1 | Power supply Electronics central electrics circuit board IOX1 |
0508 | ZE UB+ IOX2 | Power supply Output central electrics circuit board IOX2 |
0509 | ZE Ue+ IOX2 | Power supply Electronics central electrics circuit board IOX2 |
0510 | ZE UL 10 | Power supply central electrics Output 10 |
0511 | ZE UL 11 | Power supply central electrics Output 11 |
0513 | LVC | Control unit LVC (Liquid Valve Controller) |
0514 | LVC WV01 | LVC Liquid Valve Controller water valve 01 / 5-way valve suction side |
0515 | LVC WV02 | LVC Liquid Valve Controller water valve 02 / 3-way valve switch-over circulation-spraying |
0516 | LVC WV03 | LVC Liquid Valve Controller water valve 03 / 2-way valve ring line / folding boom supply |
0517 | LVC WV04 | LVC Liquid Valve Controller water valve 04 / 2-way valve cleaning |
0518 | LVC WV05 | LVC Liquid Valve Controller water valve 05 / 2-way valve pressure filter cleaning |
0519 | LVC WV06 | LVC Liquid Valve Controller water valve 06 / 2-way valve injector / illuviation valve |
0520 | LVC WV07 | LVC Liquid Valve Controller water valve 07 / 2-way valve piston diaphragm pump suction side fresh water tank |
0521 | LVC WV08 | LVC Liquid Valve Controller water valve 08 / 2-way valve filling |
0522 | LVC WV09 | LVC Liquid Valve Controller water valve 09 / 2-way valve agitator |
0523 | LVC WV10 | LVC Liquid Valve Controller water valve 10 / 2-way valve piston diaphragm pump suction aid |
0524 | LVC Sensor supply 1 | LVC Liquid Valve Controller water valve 01 / 5-way valve suction side |
0525 | LVC Sensor supply 2 | LVC Liquid Valve Controller sensor supply water valve 02 / 3-way valve switch-over circulation-spraying |
0526 | LVC Sensor supply 3 | LVC Liquid Valve Controller sensor supply water valve 03 / 2-way valve ring line / folding boom supply |
0527 | LVC Sensor supply 4 | LVC Liquid Valve Controller sensor supply water valve 04 / 2-way valve cleaning |
0528 | LVC Sensor supply 5 | LVC Liquid Valve Controller sensor supply water valve 05 / 2-way valve pressure filter cleaning |
0529 | LVC Sensor supply 6 | LVC Liquid Valve Controller sensor supply water valve 06 / 2-way valve injector / illuviation valve |
0530 | LVC Sensor supply 7 | LVC Liquid Valve Controller sensor supply water valve 07 / 2-way valve piston diaphragm pump suction side fresh water tank |
0531 | LVC Sensor supply 8 | LVC Liquid Valve Controller sensor supply water valve 08 / 2-way valve filling |
0532 | LVC Sensor supply 9 | LVC Liquid Valve Controller sensor supply water valve 09 / 2-way valve agitator |
0533 | LVC Sensor supply 10 | LVC Liquid Valve Controller sensor supply water valve 10 / 2-way valve piston diaphragm pump suction aid |
0534 | LVC Sensor In analog 1 | LVC Liquid Valve Controller sensor input analog1 water valve 01 / 5-way valve suction side |
0535 | LVC Sensor In analog 2 | LVC Liquid Valve Controller sensor input analog2 water valve 01 / 5-way valve suction side |
0536 | LVC Sensor In analog 3 | LVC Liquid Valve Controller sensor input analog3 water valve 01 / 5-way valve suction side |
0537 | LVC Sensor In analog 4 | LVC Liquid Valve Controller sensor input analog4 water valve 01 / 5-way valve suction side |
0538 | LVC Sensor In analog 5 | LVC Liquid Valve Controller sensor input analog5 water valve 01 / 5-way valve suction side |
0539 | LVC Sensor In analog 6 | LVC Liquid Valve Controller sensor input analog6 |
0540 | LVC Sensor In analog 7 | LVC Liquid Valve Controller sensor input analog7 |
0541 | LVC Sensor In analog 8 | LVC Liquid Valve Controller sensor input analog8 |
0542 | LVC Sensor In analog 9 | LVC Liquid Valve Controller sensor input analog9 |
0543 | LVC Sensor In analog 10 | LVC Liquid Valve Controller sensor input analog10 |
0544 | LVC Sensor In digital 1 | LVC Liquid Valve Controller sensor input digital1 |
0545 | LVC Sensor In digital 2 | LVC Liquid Valve Controller sensor input digital2 |
0546 | LVC Sensor In digital 3 | LVC Liquid Valve Controller sensor input digital3 water valve 03 / 2-way valve ring line / folding boom supply |
0547 | LVC Sensor In digital 4 | LVC Liquid Valve Controller sensor input digital4 water valve 03 / 2-way valve ring line / folding boom supply |
0548 | LVC Sensor In digital 5 | LVC Liquid Valve Controller sensor input digital5 water valve 04 / 2-way valve cleaning |
0549 | LVC Sensor In digital 6 | LVC Liquid Valve Controller sensor input digital6 water valve 04 / 2-way valve cleaning |
0550 | LVC Sensor In digital 7 | LVC Liquid Valve Controller sensor input digital7 water valve 06 / 2-way valve injector / illuviation valve |
0551 | LVC Sensor In digital 8 | LVC Liquid Valve Controller sensor input digital8 water valve 06 / 2-way valve injector / illuviation valve |
0552 | LVC Sensor In digital 9 | LVC Liquid Valve Controller sensor input digital9 water valve 07 / 2-way valve piston diaphragm pump suction side fresh water tank |
0553 | LVC Sensor In digital 10 | LVC Liquid Valve Controller sensor input digital10 water valve 07 / 2-way valve piston diaphragm pump suction side fresh water tank |
0554 | LVC Sensor In digital 11 | LVC Liquid Valve Controller sensor input digital11 water valve 08 / 2-way valve filling |
0555 | LVC Sensor In digital 12 | LVC Liquid Valve Controller sensor input digital12 water valve 08 / 2-way valve filling |
0556 | LVC Sensor In digital 13 | LVC Liquid Valve Controller sensor input digital13 water valve 09 / 2-way valve agitator |
0557 | LVC Sensor In digital 14 | LVC Liquid Valve Controller sensor input digital14 |
0558 | LVC Sensor In digital 15 | LVC Liquid Valve Controller sensor input digital15 |
0559 | LVC Sensor In digital 16 | LVC Liquid Valve Controller sensor input digital16 |
0560 | LVC Sensor In digital 17 | LVC Liquid Valve Controller sensor input digital17 |
0561 | LVC Sensor In digital 18 | LVC Liquid Valve Controller sensor input digital18 |
0562 | LVC Sensor In digital 19 | LVC Liquid Valve Controller sensor input digital19 |
0563 | LVC Sensor In digital 20 | LVC Liquid Valve Controller sensor input digital20 |
0564 | LVC Sensor In digital 21 | LVC Liquid Valve Controller sensor input digital21 |
0565 | LVC Sensor In digital 22 | LVC Liquid Valve Controller sensor input digital22 |
0566 | LVC Sensor In digital 23 | LVC Liquid Valve Controller sensor input digital23 |
0567 | LVC Sensor In digital 24 | LVC Liquid Valve Controller sensor input digital24 |
0625 | Speed sensor | Speed sensor |
0626 | US left outside | Ultrasonic sensor B97 left outside |
0627 | US left centre outside | Ultrasonic sensor B97a left centre outside |
0628 | US left centre | Ultrasonic sensor B48 left centre |
0629 | US left centre inside | Ultrasonic sensor B48a left centre inside |
0630 | US left inside | Ultrasonic sensor B96 left inside |
0631 | US right inside | Ultrasonic sensor B98 right inside |
0632 | US right centre inside | Ultrasonic sensor B49a right centre inside |
0633 | US right centre | Ultrasonic sensor B49 right centre |
0634 | US right centre outside | Ultrasonic sensor B99a right centre outside |
0635 | US right outside | Ultrasonic sensor B99 right outside |
0636 | Angling left outside sensor | Angle sensor bending left outside |
0637 | Angling left inside sensor | Angle sensor bending left inside |
0638 | Angling right inside sensor | Angle sensor bending right inside |
0639 | Angling right outside sensor | Angle sensor bending right outside |
0640 | Slope compensation sensor | Angle sensor slope compensation |
0641 | Pressure sensor slope compensation | Pressure sensor slope compensation |
0642 | Gyroscope slope compensation | Gyroscope slope compensation |
0643 | Valve slope compensation upper left | Pneumatic valve slope compensation upper left |
0644 | Valve slope compensation upper right | Pneumatic valve slope compensation upper right |
0645 | BC supply voltage | Control unit BoomControl supply voltage |
0646 | BC Vers. Digital IO | Control unit BoomControl supply voltage digital inputs/outputs |
0647 | BC Vers. Sensor | Control unit BoomControl power supply sensor |
0648 | BC Vers. Gyroscope valve | Control unit BoomControl power supply gyroscope pressure valve |
0649 | BC fuse digital IO | Control unit BoomControl fuse digital inputs/outputs |
0650 | BC fuse gyroscope valve | Control unit BoomControl fuse gyroscope pressure valve |
0651 | BC fuse left valves | Control unit BoomControl fuse left valves |
0652 | BC fuse right valves | Control unit BoomControl fuse right valves |
0653 | BC folding boom | Control unit BoomControl folding boom |
0654 | LVC CAN-Bus | Control unit LVC Liquid Valve Controller CAN Bus |
0700 | Folding boom | Folding boom |
0701 | Folding boom angle adjustment | Folding boom angle adjustment |
0702 | Folding boom slope compensation | Folding boom slope compensation |
0703 | Folding boom control | Folding boom control |
0704 | Folding boom damping | Folding boom horizontal suspension |
0705 | Folding boom suspension calib. | Folding boom horizontal suspension calibration |
0706 | Package interlocking | Package interlocking |
0707 | Package interlocking calib. | Package interlocking calibration |
0708 | Parallelogram | Parallelogram |
0709 | Parallelogram calib. | Parallelogram calibration |
0710 | Pendulum lock | Pendulum lock |
0711 | Pendulum lock calibration | Pendulum lock calibration |
0712 | Folding boom calibration | Folding boom calibration |
0713 | Wing | Wing |
0714 | Wing calibration | Wing calibration |
0715 | Inside wing | Inside wing |
0716 | Wing interlocking | Wing interlocking |
0717 | Wing interlocking calib. | Wind interlocking calibration |
0718 | Centre wing | Centre wing |
0719 | Outside wing | Outside wing |
0720 | Steering gyroscope | Steering gyroscope |
0721 | CANIO | CANIO / sections module |
0722 | Circulation | Circulation |
0723 | Cleaning | Cleaning |
0724 | Air cleaning | Air cleaning / blow-out function (AIR valve) |
0725 | Folding boom cleaning | Folding boom cleaning |
0726 | Dilution | Dilution |
0727 | Drain | Drain |
0728 | Main cleaning | Main cleaning |
0729 | Washing program | Washing program |
0730 | High-pressure cleaner | High-pressure cleaner |
0731 | Outside cleaning | Outside cleaning |
0732 | Diagnostics | Diagnostics |
0733 | Error memory | Error memory |
0734 | Filling | Filling |
0735 | Filter monitoring | Filter monitoring |
0736 | Filter flushing | Filter flushing |
0737 | Folding | Folding |
0738 | Folding process | Folding process |
0739 | Illuviation valve | Illuviation valve |
0740 | Valve control | Valve control |
0741 | Error memory | Error memory |
0742 | Agitator | Agitator |
0743 | Nozzle control | Nozzle control |
0744 | Pump control | Pump control |
0745 | Pump limitation | Pump limitation |
0746 | Section control | Section control |
0747 | Folding boom pressure sensor | Folding boom pressure sensor |
0748 | Cleaning pressure sensor | Cleaning pressure sensor |
0749 | Fresh water sensor | Sensor fresh water filling level |
0750 | Fresh water pressure sensor | Fresh water pressure sensor |
0751 | Agitator pressure sensor | Agitator pressure sensor |
0752 | Pump pressure sensor | Pump pressure sensor |
0753 | Solution tank sensor | Sensor wash tank filling level |
0754 | Solution tank pressure sensor | Solution tank pressure sensor |
0755 | Sprayer | Sprayer |
0756 | Spraying function | Spraying function |
0757 | Sprayer placing quantity | Sprayer placing quantity |
0758 | Rear wheel steering | Rear wheel steering |
0759 | Solution tank | Solution tank |
0760 | Fresh water tank | Fresh water tank |
0761 | Job control | Job control |
0762 | Valve WV01 | Water valve 01 / 5-way valve in suction side |
0763 | Valve WV02 | Water valve 02 / 3-way valve switch-over circulation-spraying |
0764 | Valve WV03 | Water valve 03 / 2-way vale ring line / folding boom supply |
0765 | Valve WV04 | Water valve 04 / 2-way valve cleaning |
0766 | Valve WV05 | Water valve 05 / 2-way valve pressure filter cleaning |
0767 | Valve WV06 | Water valve 06 / 2-way valve injector / illuviation valve |
0768 | Valve WV07 | Water valve 07 / 2-way valve piston diaphragm pump suction side fresh water tank |
0769 | Valve WV08 | Water valve 08 / 2-way valve filling |
0770 | Valve WV09 | Water valve 09 / 2-way valve agitator |
0771 | Valve WV10 | Water valve 10 / 2-way valve |
0772 | Calibration | Calibration |
0774 | Winter storage | Winter storage |
0775 | Filter cleaning | Filter cleaning |
0776 | Tank cleaning | |
0777 | Valve WV11 | Water valve 11 / 2-way valve tank 1 |
0778 | Valve WV12 | Water valve 11 / 2-way valve tank 2 |
0780 | BC WV02 | Control unit BoomControl water valve 02 / 3-way valve switch-over circulation-spraying |
0781 | Folding boom control ADAS | Folding boom control ADAS |
0797 | Suspension left side | Suspension left side |
0798 | Suspension right side | Suspension right side |
0799 | External control panel | External control panel |
0806 | Suspension | Suspension |
0899 | HECU | Control unit Horsch ECU |
0910 | LSB | Control unit spraying job computer Leeb Sprayer Brain |
0911 | CAN 1 LSB | CAN1 spraying job computer Leeb Sprayer Brain |
0912 | CAN 2 LSB | CAN2 spraying job computer Leeb Sprayer Brain |
0913 | CAN 3 LSB | CAN3 spraying job computer Leeb Sprayer Brain |
0914 | CAN 4 LSB | CAN4 spraying job computer Leeb Sprayer Brain |
0920 | CANIO 1 | Control unit/sections module 1 |
0921 | CANIO 1 CH1 | Control unit/sections module 1 channel/connection1 |
0922 | CANIO 1 CH2 | Control unit/sections module 1 channel/connection2 |
0923 | CANIO 1 CH3 | Control unit/sections module 1 channel/connection3 |
0924 | CANIO 1 CH4 | Control unit/sections module 1 channel/connection4 |
0925 | CANIO 2 | Control unit/sections module 2 |
0926 | CANIO 2 CH1 | Control unit/sections module 2 channel/connection1 |
0927 | CANIO 2 CH2 | Control unit/sections module 2 channel/connection2 |
0928 | CANIO 2 CH3 | Control unit/sections module 2 channel/connection3 |
0929 | CANIO 2 CH4 | Control unit/sections module 2 channel/connection4 |
0930 | CANIO 3 | Control unit/sections module 3 |
0931 | CANIO 3 CH1 | Control unit/sections module 3 channel/connection1 |
0932 | CANIO 3 CH2 | Control unit/sections module 3 channel/connection2 |
0933 | CANIO 3 CH3 | Control unit/sections module 3 channel/connection3 |
0934 | CANIO 3 CH4 | Control unit/sections module 3 channel/connection4 |
0935 | CANIO 4 | Control unit/sections module 4 |
0936 | CANIO 4 CH1 | Control unit/sections module 4 channel/connection1 |
0937 | CANIO 4 CH2 | Control unit/sections module 4 channel/connection2 |
0938 | CANIO 4 CH3 | Control unit/sections module 4 channel/connection3 |
0939 | CANIO 4 CH4 | Control unit/sections module 4 channel/connection4 |
0940 | CANIO 5 | Control unit/sections module 5 |
0941 | CANIO 5 CH1 | Control unit/sections module 5 channel/connection1 |
0942 | CANIO 5 CH2 | Control unit/sections module 5 channel/connection2 |
0943 | CANIO 5 CH3 | Control unit/sections module 5 channel/connection3 |
0944 | CANIO 5 CH4 | Control unit/sections module 5 channel/connection4 |
0945 | CANIO 6 | Control unit/sections module 6 |
0946 | CANIO 6 CH1 | Control unit/sections module 6 channel/connection1 |
0947 | CANIO 6 CH2 | Control unit/sections module 6 channel/connection2 |
0948 | CANIO 6 CH3 | Control unit/sections module 6 channel/connection3 |
0949 | CANIO 6 CH4 | Control unit/sections module 6 channel/connection4 |
0950 | CANIO 7 | Control unit/sections module 7 |
0951 | CANIO 7 CH1 | Control unit/sections module 7 channel/connection1 |
0952 | CANIO 7 CH2 | Control unit/sections module 7 channel/connection2 |
0953 | CANIO 7 CH3 | Control unit/sections module 7 channel/connection3 |
0954 | CANIO 7 CH4 | Control unit/sections module 7 channel/connection4 |
0955 | CANIO 8 | Control unit/sections module 8 |
0956 | CANIO 8 CH1 | Control unit/sections module 8 channel/connection1 |
0957 | CANIO 8 CH2 | Control unit/sections module 8 channel/connection2 |
0958 | CANIO 8 CH3 | Control unit/sections module 8 channel/connection3 |
0959 | CANIO 8 CH4 | Control unit/sections module 8 channel/connection4 |
0960 | CANIO 9 | Control unit/sections module 9 |
0961 | CANIO 9 CH1 | Control unit/sections module 9 channel/connection1 |
0962 | CANIO 9 CH2 | Control unit/sections module 9 channel/connection2 |
0963 | CANIO 9 CH3 | Control unit/sections module 9 channel/connection3 |
0964 | CANIO 9 CH4 | Control unit/sections module 9 channel/connection4 |
0965 | CANIO 10 | Control unit/sections module 10 |
0966 | CANIO 10 CH1 | Control unit/sections module 10 channel/connection1 |
0967 | CANIO 10 CH2 | Control unit/sections module 10 channel/connection2 |
0968 | CANIO 10 CH3 | Control unit/sections module 10 channel/connection3 |
0969 | CANIO 10 CH4 | Control unit/sections module 10 channel/connection4 |
0970 | CANIO 11 | Control unit/sections module 11 |
0971 | CANIO 11 CH1 | Control unit/sections module 11 channel/connection1 |
0972 | CANIO 11 CH2 | Control unit/sections module 11 channel/connection2 |
0973 | CANIO 11 CH3 | Control unit/sections module 11 channel/connection3 |
0974 | CANIO 11 CH4 | Control unit/sections module 11 channel/connection4 |
0975 | CANIO 12 | Control unit/sections module 12 |
0976 | CANIO 12 CH1 | Control unit/sections module 12 channel/connection1 |
0977 | CANIO 12 CH2 | Control unit/sections module 12 channel/connection2 |
0978 | CANIO 12 CH3 | Control unit/sections module 12 channel/connection3 |
0979 | CANIO 12 CH4 | Control unit/sections module 12 channel/connection4 |
0980 | CANIO 13 | Control unit/sections module 13 |
0981 | CANIO 13 CH1 | Control unit/sections module 13 channel/connection1 |
0982 | CANIO 13 CH2 | Control unit/sections module 13 channel/connection2 |
0983 | CANIO 13 CH3 | Control unit/sections module 13 channel/connection3 |
0984 | CANIO 13 CH4 | Control unit/sections module 13 channel/connection4 |
0985 | CANIO 14 | Control unit/sections module 14 |
0986 | CANIO 14 CH1 | Control unit/sections module 14 channel/connection1 |
0987 | CANIO 14 CH2 | Control unit/sections module 14 channel/connection2 |
0988 | CANIO 14 CH3 | Control unit/sections module 14 channel/connection3 |
0989 | CANIO 14 CH4 | Control unit/sections module 14 channel/connection4 |
0990 | CANIO 15 | Control unit/sections module 15 |
0991 | CANIO 15 CH1 | Control unit/sections module 15 channel/connection1 |
0992 | CANIO 15 CH2 | Control unit/sections module 15 channel/connection2 |
0993 | CANIO 15 CH3 | Control unit/sections module 15 channel/connection3 |
0994 | CANIO 15 CH4 | Control unit/sections module 15 channel/connection4 |
0995 | CANIO 16 | Control unit/sections module 16 |
0996 | CANIO 16 CH1 | Control unit/sections module 16 channel/connection1 |
0997 | CANIO 16 CH2 | Control unit/sections module 16 channel/connection2 |
0998 | CANIO 16 CH3 | Control unit/sections module 16 channel/connection3 |
0999 | CANIO 16 CH4 | Control unit/sections module 16 channel/connection4 |
1000 | CANIO 17 | Control unit/sections module 17 |
1001 | CANIO 17 CH1 | Control unit/sections module 17 channel/connection1 |
1002 | CANIO 17 CH2 | Control unit/sections module 17 channel/connection2 |
1003 | CANIO 17 CH3 | Control unit/sections module 17 channel/connection3 |
1004 | CANIO 17 CH4 | Control unit/sections module 17 channel/connection4 |
1005 | CANIO 18 | Control unit/sections module 18 |
1006 | CANIO 18 CH1 | Control unit/sections module 18 channel/connection1 |
1007 | CANIO 18 CH2 | Control unit/sections module 18 channel/connection2 |
1008 | CANIO 18 CH3 | Control unit/sections module 18 channel/connection3 |
1009 | CANIO 18 CH4 | Control unit/sections module 18 channel/connection4 |
1010 | CANIO 19 | Control unit/sections module 19 |
1011 | CANIO 19 CH1 | Control unit/sections module 19 channel/connection1 |
1012 | CANIO 19 CH2 | Control unit/sections module 19 channel/connection2 |
1013 | CANIO 19 CH3 | Control unit/sections module 19 channel/connection3 |
1014 | CANIO 19 CH4 | Control unit/sections module 19 channel/connection4 |
1015 | CANIO 20 | Control unit/sections module 20 |
1016 | CANIO 20 CH1 | Control unit/sections module 20 channel/connection1 |
1017 | CANIO 20 CH2 | Control unit/sections module 20 channel/connection2 |
1018 | CANIO 20 CH3 | Control unit/sections module 20 channel/connection3 |
1019 | CANIO 20 CH4 | Control unit/sections module 20 channel/connection4 |
1020 | CANIO 21 | Control unit/sections module 21 |
1021 | CANIO 21 CH1 | Control unit/sections module 21 channel/connection1 |
1022 | CANIO 21 CH2 | Control unit/sections module 21 channel/connection2 |
1023 | CANIO 21 CH3 | Control unit/sections module 21 channel/connection3 |
1024 | CANIO 21 CH4 | Control unit/sections module 21 channel/connection4 |
1025 | CANIO 22 | Control unit/sections module 22 |
1026 | CANIO 22 CH1 | Control unit/sections module 22 channel/connection1 |
1027 | CANIO 22 CH2 | Control unit/sections module 22 channel/connection2 |
1028 | CANIO 22 CH3 | Control unit/sections module 22 channel/connection3 |
1029 | CANIO 22 CH4 | Control unit/sections module 22 channel/connection4 |
1030 | CANIO 23 | Control unit/sections module 23 |
1031 | CANIO 23 CH1 | Control unit/sections module 23 channel/connection1 |
1032 | CANIO 23 CH2 | Control unit/sections module 23 channel/connection2 |
1033 | CANIO 23 CH3 | Control unit/sections module 23 channel/connection3 |
1034 | CANIO 23 CH4 | Control unit/sections module 23 channel/connection4 |
1035 | CANIO 24 | Control unit/sections module 24 |
1036 | CANIO 24 CH1 | Control unit/sections module 24 channel/connection1 |
1037 | CANIO 24 CH2 | Control unit/sections module 24 channel/connection2 |
1038 | CANIO 24 CH3 | Control unit/sections module 24 channel/connection3 |
1039 | CANIO 24 CH4 | Control unit/sections module 24 channel/connection4 |
1040 | CANIO 25 | Control unit/sections module 25 |
1041 | CANIO 25 CH1 | Control unit/sections module 25 channel/connection1 |
1042 | CANIO 25 CH2 | Control unit/sections module 25 channel/connection2 |
1043 | CANIO 25 CH3 | Control unit/sections module 25 channel/connection3 |
1044 | CANIO 25 CH4 | Control unit/sections module 25 channel/connection4 |
1045 | CANIO 26 | Control unit/sections module 26 |
1046 | CANIO 26 CH1 | Control unit/sections module 26 channel/connection1 |
1047 | CANIO 26 CH2 | Control unit/sections module 26 channel/connection2 |
1048 | CANIO 26 CH3 | Control unit/sections module 26 channel/connection3 |
1049 | CANIO 26 CH4 | Control unit/sections module 26 channel/connection4 |
1050 | CANIO 27 | Control unit/sections module 27 |
1051 | CANIO 27 CH1 | Control unit/sections module 27 channel/connection1 |
1052 | CANIO 27 CH2 | Control unit/sections module 27 channel/connection2 |
1053 | CANIO 27 CH3 | Control unit/sections module 27 channel/connection3 |
1054 | CANIO 27 CH4 | Control unit/sections module 27 channel/connection4 |
1055 | CANIO 28 | Control unit/sections module 28 |
1056 | CANIO 28 CH1 | Control unit/sections module 28 channel/connection1 |
1057 | CANIO 28 CH2 | Control unit/sections module 28 channel/connection2 |
1058 | CANIO 28 CH3 | Control unit/sections module 28 channel/connection3 |
1059 | CANIO 28 CH4 | Control unit/sections module 28 channel/connection4 |
1060 | CANIO 29 | Control unit/sections module 29 |
1061 | CANIO 29 CH1 | Control unit/sections module 29 channel/connection1 |
1062 | CANIO 29 CH2 | Control unit/sections module 29 channel/connection2 |
1063 | CANIO 29 CH3 | Control unit/sections module 29 channel/connection3 |
1064 | CANIO 29 CH4 | Control unit/sections module 29 channel/connection4 |
1065 | CANIO 30 | Control unit/sections module 30 |
1066 | CANIO 30 CH1 | Control unit/sections module 30 channel/connection1 |
1067 | CANIO 30 CH2 | Control unit/sections module 30 channel/connection2 |
1068 | CANIO 30 CH3 | Control unit/sections module 30 channel/connection3 |
1069 | CANIO 30 CH4 | Control unit/sections module 30 channel/connection4 |
1070 | CANIO 31 | Control unit/sections module 31 |
1071 | CANIO 31 CH1 | Control unit/sections module 31 channel/connection1 |
1072 | CANIO 31 CH2 | Control unit/sections module 31 channel/connection2 |
1073 | CANIO 31 CH3 | Control unit/sections module 31 channel/connection3 |
1074 | CANIO 31 CH4 | Control unit/sections module 31 channel/connection4 |
1075 | CANIO 32 | Control unit/sections module 32 |
1076 | CANIO 32 CH1 | Control unit/sections module 32 channel/connection1 |
1077 | CANIO 32 CH2 | Control unit/sections module 32 channel/connection2 |
1078 | CANIO 32 CH3 | Control unit/sections module 32 channel/connection3 |
1079 | CANIO 32 CH4 | Control unit/sections module 32 channel/connection4 |
1080 | CANIO 33 | Control unit/sections module 33 |
1081 | CANIO 33 CH1 | Control unit/sections module 33 channel/connection1 |
1082 | CANIO 33 CH2 | Control unit/sections module 33 channel/connection2 |
1083 | CANIO 33 CH3 | Control unit/sections module 33 channel/connection3 |
1084 | CANIO 33 CH4 | Control unit/sections module 33 channel/connection4 |
1085 | CANIO 34 | Control unit/sections module 34 |
1086 | CANIO 34 CH1 | Control unit/sections module 34 channel/connection1 |
1087 | CANIO 34 CH2 | Control unit/sections module 34 channel/connection2 |
1088 | CANIO 34 CH3 | Control unit/sections module 34 channel/connection3 |
1089 | CANIO 34 CH4 | Control unit/sections module 34 channel/connection4 |
1090 | CANIO 35 | Control unit/sections module 35 |
1091 | CANIO 35 CH1 | Control unit/sections module 35 channel/connection1 |
1092 | CANIO 35 CH2 | Control unit/sections module 35 channel/connection2 |
1093 | CANIO 35 CH3 | Control unit/sections module 35 channel/connection3 |
1094 | CANIO 35 CH4 | Control unit/sections module 35 channel/connection4 |
1095 | CANIO 36 | Control unit/sections module 36 |
1096 | CANIO 36 CH1 | Control unit/sections module 36 channel/connection1 |
1097 | CANIO 36 CH2 | Control unit/sections module 36 channel/connection2 |
1098 | CANIO 36 CH3 | Control unit/sections module 36 channel/connection3 |
1099 | CANIO 36 CH4 | Control unit/sections module 36 channel/connection4 |
1100 | CANIO 37 | Control unit/sections module 37 |
1101 | CANIO 37 CH1 | Control unit/sections module 37 channel/connection1 |
1102 | CANIO 37 CH2 | Control unit/sections module 37 channel/connection2 |
1103 | CANIO 37 CH3 | Control unit/sections module 37 channel/connection3 |
1104 | CANIO 37 CH4 | Control unit/sections module 37 channel/connection4 |
1105 | CANIO 38 | Control unit/sections module 38 |
1106 | CANIO 38 CH1 | Control unit/sections module 38 channel/connection1 |
1107 | CANIO 38 CH2 | Control unit/sections module 38 channel/connection2 |
1108 | CANIO 38 CH3 | Control unit/sections module 38 channel/connection3 |
1109 | CANIO 38 CH4 | Control unit/sections module 38 channel/connection4 |
1110 | CANIO 39 | Control unit/sections module 39 |
1111 | CANIO 39 CH1 | Control unit/sections module 39 channel/connection1 |
1112 | CANIO 39 CH2 | Control unit/sections module 39 channel/connection2 |
1113 | CANIO 39 CH3 | Control unit/sections module 39 channel/connection3 |
1114 | CANIO 39 CH4 | Control unit/sections module 39 channel/connection4 |
1115 | CANIO 40 | Control unit/sections module 40 |
1116 | CANIO 40 CH1 | Control unit/sections module 40 channel/connection1 |
1117 | CANIO 40 CH2 | Control unit/sections module 40 channel/connection2 |
1118 | CANIO 40 CH3 | Control unit/sections module 40 channel/connection3 |
1119 | CANIO 40 CH4 | Control unit/sections module 40 channel/connection4 |
1120 | CANIO 41 | Control unit/sections module 41 |
1121 | CANIO 41 CH1 | Control unit/sections module 41 channel/connection1 |
1122 | CANIO 41 CH2 | Control unit/sections module 41 channel/connection2 |
1123 | CANIO 41 CH3 | Control unit/sections module 41 channel/connection3 |
1124 | CANIO 41 CH4 | Control unit/sections module 41 channel/connection4 |
1125 | CANIO 42 | Control unit/sections module 42 |
1126 | CANIO 42 CH1 | Control unit/sections module 42 channel/connection1 |
1127 | CANIO 42 CH2 | Control unit/sections module 42 channel/connection2 |
1128 | CANIO 42 CH3 | Control unit/sections module 42 channel/connection3 |
1129 | CANIO 42 CH4 | Control unit/sections module 42 channel/connection4 |
1133 | Sprayray | MSO Sprayray sensors |
1137 | SV suspension right up | |
1138 | SV suspension right down | |
1139 | SV suspension left up | |
1140 | SV suspension left down | |
1143 | SV cleaning pump | Solenoid valve cleaning pump |
1193 | Hydraulic release | Hydraulics lockout switch |
1195 | External filling pump |