Overview PT Base vehicle

Error type number Error type What to do? Description
001 Short-circuit Electrical inspection: Cable, sensor contacts Conduct short-circuit test.
002 Interruption Electrical inspection: Cable, sensor contacts Conduct interruption test.
003 Short-circuit Electrical inspection: Cable, sensor contacts Conduct short-circuit test.
004 Interruption Electrical inspection: Cable, sensor contacts Conduct interruption test.
006 Sensor not taught Teach/calibrate sensor Sensor not taught/calibrated. Conduct teaching.
011 CAN BUS overflow Too many message on CAN BUS, possibly malfunction of a subscriber.
Check terminating resistors		 Too many messages on the CAN BUS.
013 Standard parameter set Enter vehicle-specific parameter set manually or load with ServiceTool. Control unit was reset to default parameter set.
Possible causes: Wrong shut-off of the ECU by unplugging during operation, loose contact or battery buffer.
018 Busheavy CAN Bus faulty, check CAN Bus wiring Electrical fault in CAN BUS system
019 Buslight CAN Bus faulty, check CAN Bus wiring Electrical fault in CAN BUS system
020 Busoff CAN Bus faulty, check CAN Bus wiring Electrical fault in CAN BUS system
021 Manual override on Restart system or shut off manual overlay. One or several inputs were overlaid with a manual value in the diagnostics menu.
022 Current too high Electrical inspection according to circuit diagram.
Wiring, consumer, control unit.		 Permitted current at the respective output of the control unit concerned exceeded.
023 Partial failure Electrical inspection according to circuit diagram.
Wiring, control unit.
Use control unit-specific diagnostic tool.		 Restricted function of the respective control unit.
024 Coil Electrical inspection according to circuit diagram.
Wiring, control unit.
Use control unit-specific diagnostic tool.		 Malfunction of travel drive magnet coil
025 Frequency front left Electrical inspection according to circuit diagram.
Wiring, control unit.
Check sensor for setting and mechanical damage.		 Implausible frequency of travel drive wheel speed sensor
026 Frequency front right Electrical inspection according to circuit diagram.
Wiring, control unit.
Check sensor for setting and mechanical damage.		 Implausible frequency of travel drive wheel speed sensor
027 Frequency rear left Electrical inspection according to circuit diagram.
Wiring, control unit.
Check sensor for setting and mechanical damage.		 Implausible frequency of travel drive wheel speed sensor
028 Frequency rear right Electrical inspection according to circuit diagram.
Wiring, control unit.
Check sensor for setting and mechanical damage.		 Implausible frequency of travel drive wheel speed sensor
029 Travel direction switch Electrical inspection according to circuit diagram.
Wiring, plug-and-socket connections, travel direction switch, control unit.
 Implausible signal of travel direction switch.
Interruption, short-circuit, two positions simultaneously.
030 Trav dr strt cond Set travel pedal or travel direction switch to neutral.
Electrical inspection according to circuit diagram.
Wiring, plug-and-socket connections, control unit.		 Travel pedal or travel direction switch operated at system start
032 Hydraulic oil temp. too high Check cooling system.
Electrical inspection according to circuit diagram.
Wiring, control unit.
 The travel drive signals excessive oil temperature
035 Travel pedal Electrical inspection according to circuit diagram.
Wiring, plug-and-socket connections, travel pedal, control unit.
 Implausible signal of travel pedal.
Interruption, short-circuit.
036 Signal control handle Electrical inspection according to circuit diagram.
Wiring, plug-and-socket connections, armrest, joystick, control unit.
 No communication with joystick
038 Steering Electrical inspection according to circuit diagram.
Wiring, control unit.
Use control unit-specific diagnostic tool.		 Malfunction magnet coil seat valves rear axle steering
039 Parking brake Electrical inspection according to circuit diagram.
Wiring, control unit.
Use control unit-specific diagnostic tool.		 Malfunction Autohold magnet coil
048 Excess voltage Check electric system of control unit mentioned. Overvoltage in the supply of the respective control unit
049 Short-circuit to ground Check electric system of component mentioned. Short-circuit to earth on outputs of travel drive switched via earth.
050 Short-circuit Check the electric system. Short-circuit to supply voltage.
051 Undervoltage Electrical inspection according to circuit diagram.
Wiring, plug-and-socket connections, travel direction switch, control unit.
 Undervoltage in the supply of the respective control unit
052 Outside of range Electrical inspection according to circuit diagram.
Wiring, plug-and-socket connections, control unit.
 Voltage levels, signals from sensors, etc. are not in the defined range
053 Interruption Electrical inspection: Cables, contacts, Component was disconnected from control unit.
054 Critical current Electrical inspection: Cables, contacts, Current level outside valid range but no short-circuit yet.
This may cause damages in the long run.
055 Critical temperature Temperature cool-down Critical temperature may cause damages in the long run.
056 Speed too low Increase the rotary speed Speed too low
057 Hardware not compatible Use different hardware Hardware not compatible
058 Danger of overheating Temperature cool-down Danger of overheating
060 Defective Electrical inspection: Cables, contacts, Outputs or magnets defective
064 Analysing failed Developer error: Parsing of objects for Pool ABT/Dashboard failed Pool needs to be revised
070 Pool vers unsuitl Flash released software according to released bundle. Software version from LSB to ABT or HECU to dashboard not compatible
083 low Act according to the fault location low
084 high Act according to the fault location high
085 too high Act according to the fault location too high
086 value invalid Act according to the fault location Value implausible
087 no communication Act according to the fault location Communication failure
088 unknown case Act according to the fault location Wird vom Motor geschickt, mit dem Ort "Motor PLD/MR2\
089 Reports error message Contact HORSCH Service Unknown motor fault
090 Single-wire operation Electrical inspection CAN Bus ADM3: Cables, contacts, resistors Engine (ADM3) is in single-wire operation in regard to CAN.
091 Power supply too low Increase supply voltage.
Electrical inspection: Cables, contacts.		 Travel drive, battery voltage too low (smaller 9 V), vehicle looses moment, vehicle coasts.
092 Power supply too high Lower supply voltage.
Electrical inspection: Cables, contacts.		 Travel drive, battery voltage too high (greater 16 V), vehicle slows down via ramp and stops. Emergency operation possible
093 Power supply sensor 1 Electrical inspection: Cables, contacts, sensors Travel drive, sensor supply not within tolerance. Vehicle slows down via ramp and stops. Emergency operation possible
094 Power supply sensor 2 Electrical inspection: Cables, contacts, sensors Travel drive, sensor supply not within tolerance. Vehicle slows down via ramp and stops. Emergency operation possible
095 ASC/ABS error Electrical inspection: Cables, contacts, sensors Travel drive, disabled due to faulty signals or wheel sensors or steering. ASR and ABS not active. Vehicle slows down via ramp and stops. Emergency operation possible.
096 CAN J1939 EEC1 Electrical inspection: Cables, contacts, control unit Travel drive, time-out EEC1 message, CAN Bus interruption, diesel control unit defective. Travel drive looses moment. Vehicle coasts down
097 CAN HECU Electrical inspection: Cables, contacts, control unit Travel drive, time-out HECU message, CAN Bus interruption, HECU defective. Travel drive looses moment. Vehicle coasts. Travel drive is disabled.
098 Forward coil Electrical inspection: Cables, contacts, control unit, coil Travel drive, pump 1 forward magnet: Short-circuit to earth, short-circuit to supply, cable break release, outputs deactivated, defective magnet. Travel drive looses moment. Vehicle coasts.
099 Reverse coil Electrical inspection: Cables, contacts, control unit, coil Travel drive, pump 1 backward magnet: Short-circuit to earth, short-circuit to supply, cable break release, outputs deactivated, defective magnet. Travel drive looses moment. Vehicle coasts.
101 Not possible Action according to fault location Action (see fault location) cannot be executed
110 CAN protocol incompatible Contact HORSCH Service Development fault, CAN protocol of subscriber (see fault location) not as expected
117 Steering not centred Centre steering. Rear axle steering not in centre position. It must be centred for the desired request.
121 not calibrated The system must be calibrated for the full range of functions. However, this has not happened with one area (see fault location)
132 Parameter value invalid Parameter value of another subscriber (see fault location) could not be accepted
137 Sensor value invalid The value of a sensor (see fault location) is outside a valid range
145 Communication error Communication of a CAN subscriber (see fault location) is interrupted longer than permitted
154 Speed too high Because of the current process on the folding boom the current speed is too high for the process on rear axle steering
155 not forward Cruise control can only be enabled in forward travel direction
156 insert The parking brake must be engaged for the current process
157 locked If rear axle steering shall be activated in road travel mode
158 not locked When switching from field mode to road travel mode and rear axle steering cannot be locked
159 not in centre position When switching from field mode to road travel mode and rear axle steering is not in the centre position
160 not retracted When switching from field mode to road travel mode and an object (see fault location) was not moved into road travel mode
161 start The engine must be started for the desired process
162 not in field mode The vehicle must be moved into field mode for the desired process
163 too low A value (see fault location) is too low for the desired process
169 Access level 1 activated Functions enabled under access level 1
170 Access level 2 activated Functions enabled under access level 2
175 Drive 100 m and confirm A distance of 100 m must be travelled to calibrate the speed
200 Air filter full Check air filter
Clean the air filter
Replace air filter.		 Air volume insufficient, air filter clogged
201 Cooling water level too low Refill cooling water
Check cooling system for leaks
Ensure that cooling water contains sufficient anti-freeze.		 Engine coolant under minimum value
202 Engine oil level too low Replenish engine oil (see operating instructions) Engine oil has dropped below minimum limit
203 Engine oil pressure too low Shut down engine immediately to prevent further damages; visit a qualified workshop. No adequate engine oil pressure can be built up
204 Check engine! Contact Service.
Read out engine error.
Have malfunction corrected by qualified workshop.		 A less serious fault is present where the vehicle does not need to be stopped immediately.
205 Stop vehicle! Engine off! Stop vehicle immediately and shut down the engine. Have malfunction corrected by qualified workshop. A serious fault is present where the vehicle must be stopped immediately.
206 Filling level low The medium (see fault location) has just reached the reserve level
207 Filling level critical The medium (see fault location) has soon depleted the reserve level
208 Water level in filter too high Water separator must drained Water separator for fuel is full
209 Temperature too high Permissible working temperature for an object (see fault location) was exceeded
210 Oil filter leaktight Check / change hydraulic oil filter Hydraulic oil filter is full
212 FA pressure faulty The sensor for the front axle pressure supplies a value outside the valid range
213 Emergency operation Travel drive signals that it can only be operated now in emergency mode
214 Engine hood open Close the engine hood and check the interlocking. Engine hood not fully locked
215 Accumulator charge pressure too low The minimum value for the accumulation charge pressure was fallen below for the service brake
216 Deviation too great The value of the object (see fault location) is outside its defined range
217 Malfunction The object (see fault location) exhibits faulty behaviour
219 Voltage drop Travel drive signals a weak battery
220 High pressure reverse travel drive High pressure reverse travel drive. Sensors outside the permissible range, short-circuit to earth, short-circuit to supply. Travel drive looses moment. Vehicle coasts. Emergency operation possible.
221 High pressure forward travel drive High pressure forward travel drive. Sensors outside the permissible range, short-circuit to earth, short-circuit to supply. Travel drive looses moment. Vehicle coasts. Emergency operation possible.
222 Brake pedal Travel drive signals short-circuit to earth, short-circuit to supply, wire break, on brake pedal. Vehicle slows down via ramp and stops. Emergency operation possible.
223 Brake pressure Travel drive signals short-circuit to earth, short-circuit to supply, wire break, at input of brake pressure. Vehicle slows down via ramp, stops. Emergency operation possible
224 Emergency-Off Travel drive signals emergency stop because it has either been activated manually, the ramp-up procedure was stopped or end stage enabling (proportional and switching outputs) has been deactivated. The travel drive will not work then.
225 Ignore monitoring Travel drive signals, hardware monitor detected fault but was ignored. For information only
226 Emergency operation monitoring Travel drive signals, hardware monitor detected fault and caused limp-home mode. Vehicle slows down via ramp
227 Stop monitoring Travel drive signals, hardware monitor detected fault and causes stop. Vehicle slows down via ramp and stops.
228 Switch monitoring Travel drive signals, hardware monitor detected fault and caused stop. Vehicle slows down via ramp and stops.
229 Access level 1 required
237 Laboratory test Travel drive signals lab test marker, development version for lab. Vehicle cannot be operated
238 Pressure sensor installation Travel drive signals, pressure sensors forward and reverse are swapped. Vehicle slows down via ramp and stops. Emergency operation possible.
239 reduced speed Travel drive signals, hydraulic oil temperature > 90 °C. Travel speed limited in all gears to 70%
240 Restart after software update Travel drive signal new software must be restarted
241 CAN control console Travel drive signals no CAN connection to control console. Vehicle slows down via ramp and stops. Normal operation possible with travel pedal
242 Direction front left Travel drive signals, wheel direction sensor front left, short-circuit to earth, short-circuit to supply or wire break. Vehicle slows down via ramp and stops. Emergency operation possible.
243 Direction front right Travel drive signals, wheel direction sensor front right, short-circuit to earth, short-circuit to supply or wire break. Vehicle slows down via ramp and stops. Emergency operation possible.
244 Direction rear left Travel drive signals, wheel direction sensor rear left, short-circuit to earth, short-circuit to supply or wire break. Vehicle slows down via ramp and stops. Emergency operation possible.
245 Direction rear right Travel drive signals, wheel direction sensor rear right, short-circuit to earth, short-circuit to supply or wire break. Vehicle slows down via ramp and stops. Emergency operation possible.
246 Basic power supply low Travel drive signals, ramp-up procedure interrupted since supply voltage smaller than 8.5 V. Travel drive not working.
247 Supply voltage Travel drive signals, ramp-up procedure interrupted since supply voltage faulty. Travel drive not working.
248 Hardware monitoring 1 Travel drive signals, ramp-up procedure interrupted since internal system test failed. Travel drive not working.
249 Hardware monitoring 2 Travel drive signals, ramp-up procedure interrupted since internal system test failed. Travel drive not working.
250 Start-up condition 1 Travel drive signals, ramp-up procedure interrupted since start condition before closing of central switch not met. (Speed sensors detect rolling vehicle) Travel drive not working
251 Start-up condition 2 Travel drive signal, ramp-up procedure interrupted since start condition before closing of central switch not met. (Travel lever not in neutral position, pedal not at zero, joystick no in neutral), travel drive not working
252 speed Travel drive signals, ramp-up procedure interrupted since starting condition diesel speed not met (speed > 400 rpm)
253 Short-circuit Travel drive signals, security violation short-circuit. Ramp-up procedure stopped, shut-down test PWM outputs failed. Travel drive not working
254 Wire break Travel drive signals, security violation wire break. Ramp-up procedure stopped, shut-down test PWM outputs failed. Travel drive not working
255 Circuit breaker 1 Travel drive signals, circuit breaker 1, ramp-up procedure stopped, switch-on of power supply no longer possible because of internal faults. Travel drive not working
256 Circuit breaker 2 Travel drive signals, circuit breaker 2, ramp-up procedure stopped, switch-on of power supply no longer possible because of internal faults. Travel drive not working
257 Electric power supply Travel drive signals, ramp-up procedure stopped, no supply voltage for power supply. Travel drive not working.
258 Power reduced Travel drive signals, ramp-up procedure stopped, unexpected voltage after central switches, although central switch open. Travel drive not working.
259 Emergency operation Travel drive signals, limp-home operation limp home. Error display only.
260 No parking brake pressure Travel drive signals, no parking brake pressure. Short-circuit to earth, short-circuit to supply, cable break, check hydraulics. Vehicle slows down via ramp and stops. Limp home must be activated via HECU. Limp home driving is then possible.
261 actuate Information, to start the engine via the button the brake pedal must be pressed at the same time.
262 Absent Alive message Travel drive signals, no alive message of HECU received or counter does not supply ascending number. Travel drive looses moment. Vehicle coasts. Travel drive is disabled.
263 Steering lock 1 Travel drive signals, rear axle interlock 1, short-circuit to earth, short-circuit to supply, cable break, release outputs deactivated, defective magnet. Rear axle steering not released by travel computer.
264 Steering lock 2 Travel drive signals, rear axle interlock 2, short-circuit to earth, short-circuit to supply, cable break, release outputs deactivated, defective magnet. Rear axle steering not released by travel computer.
265 CAN BUS 2 off Travel drive signals, bus off on CAN 2 of travel drive computer. Engine is selected with lower idle speed.
266 CAN BUS 3 off Travel drive signals, bus off on CAN 2 of travel drive computer. Error display only
267 Command 0 Travel drive signals, missing HECU message Command message 0. Error display only.
268 Command 1 Travel drive signals, missing HECU message Command message 1. Error display only.
269 Command 2 Travel drive signals, missing HECU message Command message 2. Error display only.
270 Information Travel drive signals, missing HECU message INFO. Error display only.
271 Neutral button Travel drive signals, neutral button supplies constant ON signal. Vehicle slows down via ramp and stops. Normal operation possible with travel pedal.
272 CAN J1939 EEC2 Travel drive signals , Timeout EEC2 message CAN Bus interruption. Diesel control unit defective. Vehicle slows down via ramp and stops. Emergency operation possible.
273 CAN J1939 TSC1 Travel drive signals, TSC1 message could not be sent. Check CAN Bus, CAN Bus interruption, engine control unit defective. Engine is selected with lower idle speed.
274 Unlock reversing switch Travel drive signals, travel direction switch backward supplies constant ON signal. Vehicle slows down via ramp and stops. Normal operation possible with travel pedal.
275 Travel direction forward Travel drive signals, FNR forward contact supplies constant ON signal. Vehicle slows down via ramp and stops. Normal operation possible with travel pedal.
276 Travel direction backward Travel drive signals, FNR backward contact supplies constant ON signal. Vehicle slows down via ramp and stops. Normal operation possible with travel pedal.
277 Protocol version Travel drive signals, wrong HECU protocol version detected. Travel drive not working.
278 No function Travel drive signals, object (see fault location) does not exhibit any function and is ignored. Heed additional error message. Normal operation possible with other control functionality.
279 Parking brake sensor Travel drive signals, parking brake sensor short-circuit to earth, short-circuit to supply, wire break. Vehicle slows down via ramp and stops. Emergency operation possible.
280 Pedal pressed Travel drive signals, during ramp-up of the control unit of the travel drive a pedal setpoint unequal 0 is permanently applied. Normal operation with joystick possible.
281 Control handle active Travel drive signals, during ramp-up of the control unit of the travel drive a joystick setpoint unequal 0 is permanently applied. Normal operation possible with travel pedal.
282 Travel direction switch not in neutral Travel drive signals, during ramp-up of the control unit of the travel drive a travel direction signal of the FNR is permanently applied. Normal operation with joystick possible.
283 Suspension overload The pressure in the suspension is too high on one side of the vehicle (see fault location).
284 Suspension relief The pressure in the suspension is too low on one side of the vehicle (see fault location).
285 Plausibility error Travel drive signals, ratio between brake pedal travel and brake pressure faulty. Error display only.
286 Fan already running in reverse
287 Switched to road travel mode Information when switching from field mode to road travel mode if components are not in road travel mode. Observe additional messages.
288 please min and max value When teaching the pedals, lower and upper limits must be stored since the value is otherwise not accepted by the travel drive.
289 Value not accepted Travel drive did not accept the teach value
290 Suspension relief
295 too low Value (see fault location) has fallen below defined limit
299 Parameter index invalid Travel drive signals that the parameter with the index does not exist.
300 Hydr. oil temp. too low Fan can only be reversed when the hydraulic oil has reached a minimum temperature
349 Error Button Wu The Claas armrest signals that the Wu button has a malfunction.
350 Error Button Cvtmc The Claas armrest signals that the Cvtmc button has a malfunction.
351 Error Button M1 The Claas armrest signals that the M1 button has a malfunction.
352 Error Button MPlus The Claas armrest signals that the MPlus button has a malfunction.
353 Error Button StSs The Claas armrest signals that the StSs button has a malfunction.
354 Error Button S1 The Claas armrest signals that the S1 button has a malfunction.
355 Error Button Ap The Claas armrest signals that the Ap button has a malfunction.
356 Error Button F1 The Claas armrest signals that the F1 button has a malfunction.
357 Error Button SrM2 The Claas armrest signals that the SrM2 button has a malfunction.
358 Error Button F3 The Claas armrest signals that the F3 button has a malfunction.
359 Error Button EpxyEn The Claas armrest signals that the EpxyEn button has a malfunction.
360 Error Button CcHs The Claas armrest signals that the CcHs button has a malfunction.
361 Error Button Ok The Claas armrest signals that the Ok button has a malfunction.
362 Error Button Esc The Claas armrest signals that the Esc button has a malfunction.
363 Error Button Dac The Claas armrest signals that the Dac button has a malfunction.
364 Error Button B1 The Claas armrest signals that the B1 button has a malfunction.
365 Error Button Eh1Fa The Claas armrest signals that the Eh1Fa button has a malfunction.
366 Error Button F7 The Claas armrest signals that the F7 button has a malfunction.
367 Error Button F5 The Claas armrest signals that the F5 button has a malfunction.
368 Error Button R The Claas armrest signals that the R button has a malfunction.
369 Error Button Fh The Claas armrest signals that the Fh button has a malfunction.
370 Error Button Diff The Claas armrest signals that the Diff button has a malfunction.
371 Error Button Wdd The Claas armrest signals that the Wdd button has a malfunction.
372 Error Button Sfa The Claas armrest signals that the Sfa button has a malfunction.
373 Error Button Auto The Claas armrest signals that the Auto button has a malfunction.
374 Error Button Feh The Claas armrest signals that the Feh button has a malfunction.
375 Error Joystick BigAxisY The Claas armrest signals that the joystick BigAxisY has a malfunction.
376 Error Pot. Pos The Claas armrest signals that the potentiometer Pos has a malfunction.
377 Error Pot. Epa The Claas armrest signals that the potentiometer Epa has a malfunction.
378 Error Pot. Epc The Claas armrest signals that the potentiometer Epc has a malfunction.
379 Error Joystick MiniAxisY The Claas armrest signals that the joystick MiniAxisY has a malfunction.
380 Error Poti. Fhp The Claas armrest signals that the potentiometer Fhp has a malfunction.
381 Error Poti. Epd The Claas armrest signals that the potentiometer Epd has a malfunction.
382 Error Encoder Cd The Claas armrest signals that the encoder Cd has a malfunction.
388 Parameter not synchronised Synchronising process with the travel drive could not be completed since deviating parameters may only be written when the engine is off.
389 No complied with
390 Service due A service interval has elapsed
391 500 h service overdue The 500 h service interval has been exceeded by XXX hours
Error location number Error location Description
0098 Brake pedal Brake pedal
0099 A/C compressor A/C compressor
0100 Track width front left Track width front left
0101 Track width front right Track width front right
0102 Track width rear left Track width rear left
0103 Track width right rear Track width right rear
0104 Steering angle front left Steering angle front left
0105 Steering angle rear right Steering angle rear right
0106 Hydraulic oil temp. Hydraulic oil temp.
0107 Suspension pressure front right Suspension pressure front right
0108 Cleanfix fan Cleanfix fan
0109 Service brake Service brake
0110 Suspension pressure front left Suspension pressure front left
0111 Hydraulics oil level Hydraulics oil level
0112 Steering oil pressure Steering oil pressure
0113 Diesel filter water Diesel filter water
0114 Cooling water level Cooling water level
0115 Soiled oil filter Soiled oil filter
0116 Suspension pressure rear left Suspension pressure rear left
0117 Steering angle front right Steering angle front right
0118 Steering angle rear left Steering angle rear left
0119 Spring travel front left Spring travel front left
0120 Suspension pressure rear right Suspension pressure rear right
0121 Engine hood Engine hood
0122 Spring travel rear left Spring travel rear left
0123 Spring travel front right Spring travel front right
0124 Parking brake pressure Parking brake pressure
0125 Spring travel right rear Spring travel right rear
0126 Rear axle steering release Rear axle steering release
0127 Air filter soiled Air filter soiled
0128 Seat switch Seat switch
0129 Solenoid valve: rear axle steering left Solenoid valve: Steer rear axle steering left
0130 Solenoid valve Solenoid valve: Steer rear axle steering right
0131 Solenoid valve: B ladder Solenoid valve: B ladder
0133 Solenoid valve: preselection A Solenoid valve: Pre-selection A
0134 Solenoid valve: preselection B Solenoid valve: Pre-selection B
0135 Solenoid valve: rear axle steering lock (2x) Solenoid valve: Rear axle steering lock
0136 Solenoid valve: rear axle steering lock Solenoid valve: Rear axle steering lock
0137 Solenoid valve: track rear left a Solenoid valve: Track rear left a
0138 Solenoid valve: track rear left b Solenoid valve: Track rear left b
0139 Solenoid valve: track rear right a Solenoid valve: Track rear right a
0140 Solenoid valve: track rear right b Solenoid valve: Track rear right b
0141 Parking brake relay Parking brake relay
0142 Solenoid valve: A ladder Solenoid valve: A ladder
0143 Solenoid valve: fan coupling Solenoid valve: Fan coupling
0144 Solenoid valve: track front left a Solenoid valve: Track front left a
0145 Solenoid valve: track front left b Solenoid valve: Track front left b
0146 Solenoid valve: track front right a Solenoid valve: Track front right a
0147 Solenoid valve: track front right b Solenoid valve: Track front right b
0149 Supply volt. PVED-CL Supply voltage PVED-CL
0150 Cabin signal transmitter Cabin signal transmitter
0151 Solenoid valve: height front left up Solenoid valve: Height front left up
0152 Solenoid valve: height front left down Solenoid valve: Height front left down
0153 Solenoid valve: height front right up Solenoid valve: Height front right up
0154 Solenoid valve: height front right down Solenoid valve: Height front right down
0155 Solenoid valve: height rear left up Solenoid valve: Height rear left up
0156 Solenoid valve: height rear left down Solenoid valve: Height rear left down
0157 Solenoid valve: height rear right up Solenoid valve: Height rear right up
0158 Solenoid valve: height rear right down Solenoid valve: Height rear right down
0159 Solenoid valve: seat valve front left Solenoid valve: Seat valve front left
0160 Solenoid valve: seat valve front right Solenoid valve: Seat valve front right
0161 Solenoid valve: seat valve rear left Solenoid valve: Seat valve rear left
0162 Solenoid valve: seat valve rear right Solenoid valve: Seat valve rear right
0163 Solenoid valve: damping front left Solenoid valve: Damping front left
0164 Solenoid valve: damping front right Solenoid valve: Damping front right
0165 Solenoid valve: damping rear left Solenoid valve: Damping rear left
0166 Solenoid valve: damping rear right Solenoid valve: Damping rear right
0167 Solenoid valve: Cleanfix + Solenoid valve: Cleanfix +
0168 Solenoid valve: Cleanfix - Solenoid valve: Cleanfix -
0169 Supply voltage 12 V electronics Supply voltage 12 V electronics
0170 Supply voltage 12 V power 1 Supply voltage 12 V power 1
0171 Supply voltage 12 V power 2 Supply voltage 12 V power 2
0172 Supply voltage 12 V power 3 Supply voltage 12 V power 3
0173 Supply voltage 12 V power 4 Supply voltage 12 V power 4
0174 Supply voltage 12 V power 5 Supply voltage 12 V power 5
0175 Supply voltage external Supply voltage external
0192 Track adjustment
0226 SV pendulum lock Solenoid valve pendulum lock
0247 Wheel speed sensor Wheel speed sensor
0273 Cruise control Cruise control
0274 Travel direction Direction of travel
0275 Rear axle steering rear axle steering
0276 Speed Speed
0277 Parking brake Parking brake
0294 Pressure sensor front left suspension pinned to travel drive Front left suspension pressure sensor
0295 Pressure sensor front right suspension pinned to travel drive Front right suspension pressure sensor
0296 Pressure sensor rear left suspension pinned to travel drive Rear left suspension pressure sensor
0297 Pressure sensor rear right suspension pinned to travel drive Rear right suspension pressure sensor
0298 Position sensor front left suspension pinned to travel drive Front left suspension position sensor
0299 Position sensor front right suspension pinned to travel drive Front right suspension position sensor
0300 Position sensor rear left suspension pinned to travel drive Rear left suspension position sensor
0301 Position sensor rear right suspension pinned to travel drive Rear right suspension position sensor
0302 Solenoid valve lift front left suspension pinned to travel drive Solenoid valve lift front left suspension
0303 Solenoid valve lift sensor front right suspension pinned to travel drive Solenoid valve lift front right suspension
0304 Solenoid valve lift rear left suspension pinned to travel drive Solenoid valve lift rear left suspension
0305 Solenoid valve lift rear right suspension pinned to travel drive Solenoid valve lift rear right suspension
0306 Solenoid valve lower front left suspension pinned to travel drive Solenoid valve lower front left suspension
0307 Solenoid valve lower sensor front right suspension pinned to travel drive Solenoid valve lower front right suspension
0308 Solenoid valve lower rear left suspension pinned to travel drive Solenoid valve lower rear left suspension
0309 Solenoid valve lower rear right suspension pinned to travel drive Solenoid valve lower rear right suspension
0310 Seat valve front left suspension pinned to travel drive Seat valve front left suspension
0311 Seat valve front right suspension pinned to travel drive Seat valve front right suspension
0312 Seat valve rear left suspension pinned to travel drive Seat valve rear left suspension
0313 Seat valve rear right suspension pinned to travel drive Seat valve rear right suspension
0314 Damping valve front left suspension pinned to travel drive Damping valve front left suspension
0315 Damping valve front right suspension pinned to travel drive Damping valve front right suspension
0316 Damping valve rear left suspension pinned to travel drive Damping valve rear left suspension
0317 Damping valve rear right suspension pinned to travel drive Damping valve rear right suspension
0318 Suspension control from travel drive Suspension control from travel drive
0319 Damping from travel drive Damping from travel drive
0320 Pressure in system of suspension pinned at travel drive Pressure in suspension system
0321 Service interval Service interval operating hours counter
0568 Supply voltage 5 V travel drive Supply voltage 5 V travel drive
0569 Travel drive Analog Digital Converter Travel drive Analog Digital Converter
0570 Battery Battery
0571 Speed limit travel pedal Travel drive speed restriction travel pedal
0572 Travel drive Out Digital 1 Travel drive Output Digital 1
0573 Travel drive Out Digital 2 Travel drive Output Digital 2
0574 Travel drive Out Digital 3 Travel drive Output Digital 3
0575 Travel drive Out Digital 4 Travel drive Output Digital 4
0576 Travel drive Out Digital 5 Travel drive Output Digital 5
0577 Travel drive Out Digital 6 Travel drive Output Digital 6
0578 Travel drive Out Digital 7 Travel drive Output Digital 7
0579 Travel drive Out Digital 8 Travel drive Output Digital 8
0580 Battery D1 Battery D1
0581 Battery D2 Battery D2
0582 Battery D3 Battery D3
0583 Travel drive pump 1: Travel drive pump 1:
0584 Travel drive pump 2: Travel drive pump 2:
0585 Travel drive Eeprom Travel drive Eeprom
0586 Travel drive engine Travel drive engine
0588 Brake pressure Brake pressure
0589 Travel drive CAN Travel drive CAN
0590 Speed sensor front left Speed sensor front left
0591 Speed sensor front right Speed sensor front right
0592 Speed sensor rear left Speed sensor rear left
0593 Speed sensor rear right Speed sensor rear right
0594 Travel drive seat switch Travel drive seat switch
0595 Pedal travel Pedal travel
0596 Pump 1 swivelling angle Travel drive pump 1 swivel angle sensor
0597 Pump 2 swivelling angle Travel drive pump 2 swivel angle sensor
0598 Pressure sensor front axle steering forward Pressure sensor front axle steering forward
0599 Pressure sensor front axle steering reverse Pressure sensor front axle steering reverse
0600 Pressure sensor rear axle steering forward Pressure sensor rear axle steering forward
0601 Pressure sensor rear axle steering reverse Pressure sensor rear axle steering reverse
0602 Parking brake pressure Travel drive parking brake pressure
0603 Vers. 5 V FAR internal Supply voltage 5 V travel drive internal
0604 Vers. 5 V FAR relays Supply voltage 5 V travel drive relays
0605 Control handle Control handle
0606 Travel drive Low Side DO 1 Travel drive Low Side Digital Output 1
0607 Travel drive Low Side DO 2 Travel drive Low Side Digital Output 2
0608 Travel drive Low Side DO 3 Travel drive Low Side Digital Output 3
0609 Travel drive Low Side DO 4 Travel drive Low Side Digital Output 4
0610 Travel drive Low Side DO 5 Travel drive Low Side Digital Output 5
0611 Travel drive Low Side DO 6 Travel drive Low Side Digital Output 6
0612 Travel drive Output PWM 1 Travel drive Output PWM 1
0613 Travel drive Output PWM 2 Travel drive Output PWM 2
0614 Travel drive Output PWM 3 Travel drive Output PWM 3
0615 Travel drive Output PWM 4 Travel drive Output PWM 4
0616 Travel drive Output PWM 5 Travel drive Output PWM 5
0617 Travel drive Output PWM 6 Travel drive Output PWM 6
0618 Travel drive Output PWM 7 Travel drive Output PWM 7
0619 Travel drive Output PWM 8 Travel drive Output PWM 8
0620 Travel drive SPI Bus Travel drive SPI Bus
0621 FAR Pump 1 Coil 1 Travel drive Pump 1 Coil 1
0622 FAR Pump 1 Coil 2 Travel drive Pump 1 Coil 2
0623 FAR Pump 2 Coil 1 Travel drive Pump 2 Coil 1
0624 FAR Pump 2 Coil 2 Travel drive Pump 2 Coil 2
0625 Speed sensor Speed sensor
0655 Arm rest Arm rest
0656 PVED PVED
0657 PVED SASA-Sensor PVED SASA-Sensor
0671 Engine oil level Engine oil level
0672 Engine oil pressure Engine oil pressure
0673 Engine intake air temperature Engine intake air temperature
0674 Engine cooling water temperature Engine cooling water temperature
0675 Engine battery switching voltage Engine battery switching voltage
0676 Engine system voltage Engine system voltage
0677 Engine speed Engine speed
0678 PLD/MR2 Engine PLD/MR2
0679 CAN Link ADM3 - PLD/MR2 Engine CAN Link ADM3 - PLD/MR2
0680 Injection nozzle cyl. 1 Engine injection nozzle cylinder 1
0681 Injection nozzle cyl. 2 Engine injection nozzle cylinder 2
0682 Injection nozzle cyl. 3 Engine injection nozzle cylinder 3
0683 Injection nozzle cyl. 4 Engine injection nozzle cylinder 4
0684 Injection nozzle cyl. 5 Engine injection nozzle cylinder 5
0685 Injection nozzle cyl. 6 Engine injection nozzle cylinder 6
0686 Engine prop. valve 1 Engine proportional valve 1
0687 Engine prop. valve 2 Engine proportional valve 2
0688 Engine brake valve Engine decompression brake valve
0689 Engine CAN BUS Engine CAN BUS
0690 Engine charge air temperature
0691 Engine overrun time
0700 Folding boom Folding boom
0732 Diagnostics Diagnostics
0758 Rear wheel steering Rear wheel steering
0772 Calibration Calibration
0773 Travel drive calibration Travel drive calibration
0797 Suspension left side Suspension left side
0798 Suspension right side Suspension right side
0800 Dashboard Dashboard
0801 Travel drive Travel drive
0802 Engine Engine
0803 Fuel Fuel
0804 Hydraulics Hydraulics
0805 Steering Steering
0806 Suspension Suspension
0807 Sliding axle Sliding axle
0808 Vehicle Vehicle
0809 Safety SV Susp. front lt. Front left suspension safety valve
0810 Safety SV Susp. front rt. Front right suspension safety valve
0811 Safety SV Susp. rear lt. Rear left suspension safety valve
0812 Safety SV Susp. rear rt. Rear right suspension safety valve
0813 Valve susp. front left Front left suspension valve
0814 Valve susp. front right Front right suspension valve
0815 Valve susp. rear left Rear left suspension valve
0816 Valve susp. rear right Rear right suspension valve
0817 Front steering sensor Front steering sensor
0818 Rear steering sensor Rear steering sensor
0820 VDT
0821 Travel drive hydraulic motor 1 Travel drive hydraulic motor 1
0822 Travel drive hydraulic motor 2 Travel drive hydraulic motor 2
0823 Travel drive hydraulic motor 3 Travel drive hydraulic motor 3
0824 Travel drive hydraulic motor 4 Travel drive hydraulic motor 4
0825 Travel drive status Travel drive status
0826 Travel drive hardware Travel drive hardware
0827 Travel drive wheel sensor Travel drive wheel sensor
0828 Travel drive activation Travel drive activation
0829 Travel drive rear axle Travel drive rear axle
0830 Travel drive HECU Travel drive HECU
0831 Travel drive armrest Travel drive armrest
0832 Travel drive pedal Travel drive pedal
0833 Travel drive control handle Travel drive control handle
0834 Travel drive start cond. Travel drive start condition
0835 Charge pressure Charge pressure
0836 Fan rev. not possible Fan reversal not possible
0837 Claas arm rest Claas cab armrest
0899 HECU Control unit Horsch ECU
0900 CAN 1 HECU CAN 1 Horsch ECU
0901 CAN 2 HECU CAN 2 Horsch ECU
0902 CAN 3 HECU CAN 3 Horsch ECU
0903 CAN 4 HECU CAN 4 Horsch ECU
We use cookies to optimize and continuously improve our website for you. By continuing to use the website, you agree to the use of cookies. Further information on cookies can be found in our data protection declaration More